What can I do when logged in?

You can submit new articles, so we can make unique versions of them and distribute them for you.
If you want to simply publish the same article on 800 websites, you can tell us to do that.
You can see the archive and current status of all your article distributions.
You can order any number of high-quality articles - just let us know your keywords.
You can browse the archive of all the articles we have written for you.
You can order our Complete Service (10 high-quality articles plus 10 article distributions).
You can purchase more credits for our services and check your affiliate earnings.
Much more ...

SpinDistribute.com Article Directory

The following article was published in our article directory on March 19, 2012.
Learn more about SpinDistribute Article Distribution System.

The Steps to Tile Flooring Installation

Article Category: Home Management

Author Name: Ginger Jackson

To start the tile flooring installation process the first and most important step is to make sure to take precise and accurate measurements. These measurements will be used to fit the cement board to the correct size. Score one side with a razor knife. Turn the cement board over and complete this step. The board is solid but can easily be cut to the proper size. Take special care not to remove the mesh from the board.

After all the pieces of cement board are cut, carefully lay them out on the floor. This is to double check that the fit is right. Use a cordless drill with the proper attachment or screw gun.

Use screws specially made for cement board. Space each cement board screw every 6-8 inches to fasten the cement board to the floor. Tap the tip of the screw with a hammer to start the screw then set the screws completely into the board with the drill.

It is important to find and indicate the room's center. Once the cement board is attached, it will be necessary to snap two intersecting chalk lines to mark the center of the room. Each step taken now will ensure the quality of the installation job.

The tile comes in uniformly sized sheets. Each tile has rubber dots attached to their underside. The rubber dots are simple to cut through to separate the tiles.

The dots hold the tiles together in the sheets and also act as spacers. They ensure that even grout lines are created. Use full sheets obtain the best professional look as the tile is laid out.

Lift out the tiles and spread the adhesive working in small segments. Apply the adhesive consistently and evenly using the correct trowel depth. The adhesive should be approximately the same thickness as the tiles that are being installed.

To begin to place the tiles start with the center section. Leave the more involved cuts at the perimeter of the room to the last. The adhesive dries quickly. Check the time available on the container of the product. Spread as much adhesive as possible before it dries.

After setting the beginning sheet of tiles into position, push it firmly into the adhesive to establish good contact. For the next sheet, it is very important to line up the tiles especially if it has a pattern. This is the time to check the spacing, and then set it carefully but firmly into place.

Start at the door, measuring and cutting tiles and sheets as necessary to fit the area.

To cut the tile use a wet saw. Through the entire tile flooring installation it is important to use the proper equipment and necessary safety gear.

No results found for the text you pasted (460 words). Steps to Tile Flooring Installation

To start the tile flooring installation process the first and most important step is to make sure to take precise and accurate measurements. These measurements will be used to fit the cement board to the correct size. Score one side with a razor knife. Turn the cement board over and complete this step. The board is solid but can easily be cut to the proper size. Take special care not to remove the mesh from the board.

After all the pieces of cement board are cut, carefully lay them out on the floor. This is to double check that the fit is right. Use a cordless drill with the proper attachment or screw gun.

Use screws specially made for cement board. Space each cement board screw every 6-8 inches to fasten the cement board to the floor. Tap the tip of the screw with a hammer to start the screw then set the screws completely into the board with the drill.

It is important to find and indicate the room's center. Once the cement board is attached, it will be necessary to snap two intersecting chalk lines to mark the center of the room. Each step taken now will ensure the quality of the installation job.

The tile comes in uniformly sized sheets. Each tile has rubber dots attached to their underside. The rubber dots are simple to cut through to separate the tiles.

The dots hold the tiles together in the sheets and also act as spacers. They ensure that even grout lines are created. Use full sheets obtain the best professional look as the tile is laid out.

Lift out the tiles and spread the adhesive working in small segments. Apply the adhesive consistently and evenly using the correct trowel depth. The adhesive should be approximately the same thickness as the tiles that are being installed.

To begin to place the tiles start with the center section. Leave the more involved cuts at the perimeter of the room to the last. The adhesive dries quickly. Check the time available on the container of the product. Spread as much adhesive as possible before it dries.

After setting the beginning sheet of tiles into position, push it firmly into the adhesive to establish good contact. For the next sheet, it is very important to line up the tiles especially if it has a pattern. This is the time to check the spacing, and then set it carefully but firmly into place.

Start at the door, measuring and cutting tiles and sheets as necessary to fit the area.

To cut the tile use a wet saw. Through the entire tile flooring installation it is important to use the proper equipment and necessary safety gear.

No results found for the text you pasted (460 words).  HYPERLINK "javascript:void(0);"

Keywords: Flooring, Floor Installation, Carpet Installation, Hardwood Floors, Laminate Floors, Carpet Replacement

Learn more about SpinDistribute Article Distribution System. We also offer Professional Article Writing to everyone who's looking for high quality web content.

SpinDistribute.com Network

Each article you submit at SpinDistribute.com is sent through our innovative Article Distribution System to our network of more than 1840 publishers - about 55% of them are high-quality article directories, 30% of them are niche blogs and 15% of them are other content-rich websites.

To achieve the best possible success we only publish your article to most related websites. This means your article will show up on approximately 640 - 880 most related websites which will give you great SEO results.

We also offer a separate Professional Article Writing Service to everyone who's looking for high quality web content and well researched unique articles.